Sign up to Newsletters. 220V 6 Inch Diam. Ond Core Drill Concrete Core Machine With Stand Bits Tool Drilling. Our core drilling machine combines functionality and versatility in one device. It is ideal for lighter drilling work. First, install the screw connecting the stand and the pedestal. Before use the drill, you need to fix it. Remove the two screws on the back of the stand. Seperate the stand and the pedestal. Rotate the pedesta 180° and install the screws. Here are two ways. Choose a hollow tube according to the height of the place which need to be drilled. Put one end of the tube against the. And turn the rod reversely to fix the driller tightly, expansion bolts are not needed. Make a hole on the wall or the groud and install the bolt. Install the screw rod and the stand. Then tighten the nut. Before installing, you need to smear some grease on the drill end thread in order to discharge easily. You need to run the driller at an idle state at first. Before you install or remove the drill bot, you must be sure the drill is powered off. Drill must be connected with clean cold water. Here are the ways to inject water. Using tap water: Connecting the tap and the machine with the injecting hose. Hanging a bucket over the drill. Start the drill at an idle state. Then open the water tap. When there is water flowing from the drill, you can start drilling. At first, you need to drill slowly and increase strength gradually. After you drill deeper than 5mm, you can increase your push strength. If the drill’s rotating speed decrease, than proves that the drill is overloaded. Then you need to decrease the push strength, avoiding the drill being stuck. If there is smoke coming out, you must pull out the drill right away and start. To drill after a while, avoiding the engine being burn down. When drilling reinforced concrete, current increases and the drill will vibrate. Therefore, you need to decrease pushing strength but the decreasing amplitude should not be too big. Otherwise, the effiency will be affected and the drill bit will be worn more badly. When drilling reinforced concrete containing little grains of sand and small stones, the drill may be overloaded suddenly and the drill be powered off automatically. At this time, you need to pull out the drill right away and clean the hole you drilled before you start again. When you drill woof board and thick pitch, you also need to decrease pushing and drill slowly. 6Taking out drill core. When you are going yo drill through the board or wal, you need to slow down, avoiding the drill bit being stuck. If the drill bit is stuck, you need to power off the drill immediately pull out the bit and clean it. Fetch out the drill core. Install the drill bit and start again. Attention: You should be careful when taking out the drill bit, noting damaing it. Then you need to tighten the screws to adjust the distance. At the same time, you need to make sure that the pedestal and the stand is connected firmly. This drill can be used on brick, stone, reinforced concrete, rock, and fireproof materials. Water connection with hose approx. Overload protection / slip clutch. Drill bit Ø 4.25inch /13.7inch long. 1/2 BSP threaded connection for drill bits. 2 inch mandrel on stand for quick release. The biggest drill dual purpose. 1980W infinitely variable speeds. Non water seal cage reduce maintenance costs. Aluminum alloy material ligher and steadier. Suitable for sampling concrete, cement, brick, bituminous pavement and block. Rated input power: 1980W. The largest drilling capacity: 6inch. Drill bit: 4.25inch. No-load speed: 0-980 r/min. Integrated FI (residual current circuit breaker): 10mA. Water hose length: approx. 13ft, inside Ø 0.03inch. 1 X Diamond Core Drill. 1 X Drill Bit(108mm). 1 X Ring Spanner. 1 X Monkey Wrench. 1 X Faucet Interface. 5 X Expansion Screws. 2 X Carbon Brushes. As a leading and emerging company in manufactory and exporting business, we are specialized in Business and Industrial Products, Sporting Goods, Pet Products, Home and Garden products for more than 10 years. We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. If you have any changes, pls inform us. 7:00am-13:00pm (Berlin Time). In the same day. These charges are the buyers responsibility. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage. Used items will not be accepted for return. All emails will be responded to within. Leave a Message if. You want to cancel an order. If you need further assembly instructions for a product. Any other unspecified questions or concerns. Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it’s your fault. A: The item ships from Bremen, DE. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item “220V 6Inch Diamond Core Drill Concrete Core Machine With Stand Bits Tool Driller” is in sale since Thursday, June 15, 2017. This item is in the category “Business, Office & Industrial\Power Tools\Drills\Drill Bits & Accessories\Drill Bits”. The seller is “tool-zoom” and is located in Jenec. This item can be shipped to all countries in Europe, United States, Australia.

• Brand: VEVOR
• MPN: g7874004
• Voltage (V): 220V
• Corded/ Cordless: Corded
• Power (W): 1980W
• Color: Red
• Speed: 0-980 r/min
• Drill bit: 4.25inch
• Total height: approx 30inch
• Drilling distance: approx. 19inch
• EAN: 241364395252